Installation Manuals

Model 3 Interior

Tempered Glass Touch Screen Protector

Video Link

Back Seat Cover Protector for Pets

Place the mat on your back seat and secure it with 4 belts attached to 4 head restraints (front and rear).

Model 3 Wireless Dual Mobile Speed Charging Pad

Video Link

2 Pieces Performance Pedal Set

Video Link

Trunk Insulation

Video Link

Middle Console Cover 

Clean and let dry the middle console. Remove the back foil on glue layer, begin the alignment from edges, then stick the cover on the middle console with some pressure applied.
Tip: spray a small amount of water on the middle console before installation, this will help to correct the alignment if needed.

Middle Console Organizer

Video Link

Door Protector Anti-Kicking

Clean surfaces and let dry, then apply provided glue primer on the surfaces, also quickly wipe the glue layer with the primer around edges. Apply hot air with a heat gun or hair dryer. 

Video Link

Foot Rest Pedal Stainless Steel Video Link
High-luminance LED Interior Lamps Video Link
HEPA H-14 Cabin Air Filter Replacement Set Video Link
Seat Back Anti Kick Protector Download Installation Guide
Wireless Charging Mobile Holder Video Link
Multi-layer 3D floor mats Download Installation Guide

Model 3 Exterior

Side Fender Vent Camera Trim

Clean and let dry the surface. Remove the back foil on glue layer, begin the alignment from edges, then stick the trim on with some pressure applied.

Door Handle Protection Sticker

Clean and let dry the surface. Remove the back foil on glue layer, begin the alignment from edges, then stick the wrap on with some pressure applied.

Anti-Rain Spoiler

1. Clean the back window glass with water and let dry.
2. Apply the glue primer included in the package on the surface where the spoiler will be installed.
3. Remove the back foil on glue layer, also quickly wipe the glue layer with the primer, begin the alignment from edges, then stick the spoiler on with some pressure applied.
4. Keep the spoiler dry for 24 hours, especially for the first half an hour!

NOTE: When the ambient temperature is below 5 deg.C during installation, gently apply hot air (e.g. hair dryer) on the installed spoiler body to warm it up, then apply some pressure to help the glue layer sticks better. But, in any case, not higher than 30 deg.C.

Performance Spoiler (for both OEM & Sportive)

1. Clean the car surfaces with water and let dry.
2. Apply the glue primer included in the package on the surface where the spoiler will be installed.
3. Remove the back foil on glue layer, also quickly wipe the glue layer with the primer,begin the alignment from edges, then stick the spoiler on with some pressure applied.
4. Keep the spoiler dry for 24 hours, especially for the first half an hour!

NOTE: When the ambient temperature is below 5 deg.C during installation, gently apply hot air (e.g. hair dryer) on the installed spoiler body to warm it up, then apply some pressure to help the glue layer sticks better. But, in any case, not higher than 30 deg.C.

Video Link, Download installatie template

Mist Lamp Blade Trim

1. Clean the car surfaces with water and let dry.
2. Apply the glue primer included in the package on the surface where the spoiler will be installed.
3. Remove the back foil on glue layer, also quickly wipe the glue layer with the primer,begin the alignment from edges, then stick the spoiler on with some pressure applied.
4. Keep the spoiler dry for 24 hours, especially for the first half an hour!

NOTE: When the ambient temperature is below 5 deg.C during installation, gently apply hot air (e.g. hair dryer) on the installed spoiler body to warm it up, then apply some pressure to help the glue layer sticks better. But, in any case, not higher than 30 deg.C.

Video Link

18" Rim Protector

 Video Link

Aero Wheel Cap Kit Video Link

Overall Rubber Seals (trunk+frunk+4 doors)

 Video Link

Side Fender Vent Camera Trim

 Video Link

Air Inlet Rooster

 Video Link

Frunk + Trunk Automatic Open Set

 Video Link

Front Air Deflector Lip

 Video Link

Welcome Door Projector LED Lamp

 Video Link

Power Tail Liftgate (Electric Trunk) Video Link, Installation Manual (EN & DE) Foot sensor wiring diagram.  Another alternative installation video can be find HERE.
2nd Generation Mud Flaps Video Link, Note: for Model 3 after Jan. 2020, there are no bolts provided on the rear mud flaps anymore, just install the rear mud flaps by using the plastic plugs in the same way as the front ones.
Model 3: Insulation for Front Wheels (2 pcs) Video Link

Wind Noise Reduction Kit (Rubber Seal for Glass Roof Panel Gaps)

The total length of the rubber ring is well calculated to fit your Model 3, as the gap width is variable, please adjust the diameter of the rubber ring to fit the gap sizes, use a piece of hard plastic (e.g. a bank card) to push the rubber strip further into the gaps.

To prevent the rubber ring get loose and fall out during driving, the key is to fix the ring firmly on 4 corners. To do this, stretch the rubber to make it thinner, and press the thin strip further into the glass gaps with a piece of hard plastic, especially by the corners, you may even able to push the rubber strip under the glass edge, in this way, the rubber ring is well fixed.

Model 3: Frunk Insulation Mat Video Link
Model 3: Automatic Electrical Power Frunk Video Link 

Model 3: Chrome-Delete Kit for Window Frames 

Video Link